Volkswagen Golf Mk7 Owners Manual: Wheel bolts

Fig. 222 Changing a wheel: loosening the wheel bolts

Fig. 223 Changing a wheel: tyre valve ① and locations of the anti-theft wheel bolt ② or ③

First read and observe the introductory information and safety warnings

Only the spanner delivered with the vehicle should be used to loosen the wheel bolts.

Only loosen the wheel bolts by approximately one turn before raising the vehicle with the vehicle jack.

If the wheel bolt is very tight, you may be able to loosen it by pushing down the end of the spanner carefully with your foot. Hold on to the car for support and take care not to slip.

Loosening the wheel bolts

• Fit the box spanner over the wheel bolt as far as it will go .

• Hold the end of the box spanner and turn the wheel bolt one turn anticlockwise .

Loosening the anti-theft wheel bolt

• Take the adapter for anti-theft wheel bolts out of the vehicle toolkit.

• Insert the adapter into the anti-theft wheel bolt. Push it in as far as it will go.

• Insert the box spanner into the adapter as far as it will go.

• Hold the end of the box spanner and turn the wheel bolt one turn anticlockwise .

Important information about the wheel bolts

The design of the wheel rims and wheel bolts is matched to the factory-fitted wheels. If different rims are fitted, the correct wheel bolts with the right length and correctly shaped bolt heads must be used. This ensures that wheels are fitted securely and that the brake system works properly.

In certain circumstances, wheel bolts from a vehicle of the same model series may not be used.

On wheels with a wheel cover, the anti-theft wheel bolt must be bolted into position or ③ according to the position of the tyre valve ①. Otherwise, it will not be possible to fit the wheel cover.

Tightening torque for the wheel bolts

The tightening torque for wheel bolts for steel and alloy wheels is 120 Nm. The tightening torque should be checked with a torque wrench immediately after changing a wheel.

If the wheel bolts are corroded and difficult to turn, they must be replaced and the wheel hub threads cleaned before the tightening torque is checked.

Never grease or lubricate the wheel bolts or the threads of the wheel hub. This could cause them to loosen while the vehicle is in motion, even if the required torque setting is used.

WARNING

Incorrectly tightened wheel bolts can loosen while the vehicle is in motion and cause accidents, serious injury, and loss of control of the vehicle.

• Only use wheel bolts that belong to the wheel.

• Never use different wheel bolts.

• The wheel bolts and threads of the wheel hubs must be clean, free from oil and grease, and turn easily.

• Always use the box spanner placed in the vehicle at the factory to loosen and tighten the wheel bolts.

• Only loosen the wheel bolts by approximately one turn before raising the vehicle with the vehicle jack.

• Never grease or lubricate the wheel bolts or the threads of the wheel hub. This could cause them to loosen while the vehicle is in motion, even if the required torque setting is used.

• Never remove the bolts on rims with bolted-on rings.

• If the tightening torque of the wheel bolts is too low, the wheel bolts and rims can loosen while the vehicle is in motion. The wheel bolts and threads can be damaged if the tightening torque is too high.

Questions & answers

Wheel bolts — Volkswagen Golf Mk7

How do I loosen Golf Mk7 wheel bolts?

Use the box spanner from the toolkit. Turn each bolt anti-clockwise by half a turn while the car is still on the ground. For anti-theft bolts, fit the adaptor first.

What is the Golf Mk7 anti-theft wheel bolt?

One bolt per wheel has a unique pattern that requires a matching adaptor to remove. The adaptor is in the toolkit — keep it safe, as without it the wheel cannot be removed.

What torque should Golf Mk7 wheel bolts be tightened to?

Typically 120 Nm. Tighten in a star pattern. Re-check with a calibrated torque wrench after the first 50 km of driving.

What happens if I lose the Golf Mk7 anti-theft bolt adaptor?

A replacement can be ordered from a Volkswagen dealer using the adaptor code card supplied with the vehicle. Without the adaptor, a workshop must use special tools to remove the bolts.